Call for Price
THIS ITEM IS A SPECIAL ORDER AND MAY TAKE ADDITIONAL SHIPPING TIMECTP2008 AC Chassis includes Processor, Power Supply, CLK Main, 1G RAM
Description
CTP2008 Circuit to Packet Platform (designed for USA and Australian markets *) is a 1 U rack-mountable chassis that supports up to 8 circuit emulation interfaces. The interface modules are software configurable and are the same across the CTP2000 line. Interface options include T1/E1, serial, and 4WTO analog voice.
GUARANTEED to Exceed Expectations.
When purchasing from AMNET Global, rest assured that your information technology equipment is covered for a lifetime. When you receive your order, your unit is already covered by our Lifetime Warranty and Advance Replacement.
Coverage That Never Ends.
In the event of a product malfunction, we fully understand that downtime is not an option. If you experience a product malfunction or failure, we will send you a replacement the same day, fully expedited and at our cost.
Please see our full Terms and Conditions of Warranty here.
QUESTIONS ABOUT THIS PRODUCT OR AVAILABILITY?
You have come to the right place!
If you have an immediate question, please click here and we will be glad to speak with you right away!
To speak to one of our technicians about this product, please call our technical support team at 1.888.428.6677 Option 3 and we will get you taken care of right away!
Properties
| Properties | Juniper CTP2008-AC-03 |
| Description | CTP2008 AC base chassis |
| Product Family | CTP Series |
| Product Type | Router |
| Serial Interfaces | |
| EIA-530, RS-232/V.28, RS-422/V.11, RS-423/V.10, X.21, V.35, T1, E1 | Yes |
| IRIG-B | Yes |
| Encoding NRZ, Conditioned Diphase, Isochronous, Asynchronous, AMI, B8ZS, HDB3, TDM/TDC, Transparent | Yes |
| Interface quantity | 8 |
| Rates | 50 bps–12.880 Mbps |
| Voice Interfaces | |
| Analog voice 4-wire TO interface quantity | 8 |
| 4WE&M | N/A |
| 2WFXS | N/A |
| 2WFXO | N/A |
| T1 and E1 | 8 |
| Companding conversion | N/A |
| IP Interfaces | |
| 10/100/1000BASE-T (RJ-45) | 2 |
| SFP 1000BASE-T | 4 |
| SFP 1000BASE-SX | 4 |
| SFP 1000BASE-LX | 4 |
| Precedent setting—(DSCP), configurable TOS byte | Yes |
| VLAN tagging | Yes |
| Virtual IP | Yes |
| Circuit modes—symmetric, asymmetric, unidirectional, hairpin | Yes |
| IPv4 and IPv6 | Yes |
| IETF PWE3 RFC SAToP | Yes |
| IETF PWE3 RFC CESoPSN | Yes |
| Layer 2 serial aggregation | Yes |
| Port mirroring | Yes |
| *Software support roadmap item | |
| Dimension (WxHxD) | 17.25 x 1.75 x 11.75 in (43.8 x 4.5 x 29.8 cm) |
| Weight (lb) | 12 |
| Mounting | Front Rack |
| Input voltage (AC) | 100-240 VAC |
| Power supply | 250W |
| Input current | 2 A at 110 VAC |
Specifications
| Specifications | CPT2008-AC-03 |
| Operating temperature | 32° to 104° F (0° to 40° C) |
| Humidity | 5%-90% RH noncondensing |
| Platform Features | |
| Software circuit provisioning | EIA530, RS-232, V.35, 4WTO, T1, and E1 circuit types are software configured including the line encoding, clocking, rates, and IP settings. |
| Scalable product family | A family of four CTP Series Circuit to Packet Platforms provides different port densities. Products can address the requirements of small remote sites through large central network hubs. |
| CTPView Network Management System | Secure, multi-user, web-based network management system provides network monitoring, circuit provisioning, IP performance reporting, database backup, and circuit troubleshooting tools. |
| Multiple system and circuit clocking solutions | CTP Series Circuit to Packet Platforms are designed to use multiple external clocks as monitored and prioritized system references. Circuits are configured to use the system clock, external circuit timing, or to adaptively recover clock information from the remote port when required by the application or when no reference is configured. |
| Auto switch | The status of the CTP Series circuit ports is monitored, and the circuit is automatically switched to an alternate local or remote port when a failure is detected. |
| Packet protector | Redundant packets are created and transmitted to the IP network and then processed by the receiving CTP Series. |
| Autobaud | The input timing leads are monitored, and the circuit rate is automatically changed at both ends of the network if a rate change is detected. |
| Loops and BERTs | Each CTP Series port supports interface and network loops and the ability to generate and monitor a bit error rate test with up to nine BERT patterns selectable. |
| Layer 2 Serial-to-Ethernet IP aggregation | The CTP Series Circuit to Packet Platforms can aggregate layer 2 traffic from serial interfaces onto a Fast Ethernet or Gigabit Ethernet interface. Layer 2 protocols supported are Frame Relay, PPP and Cisco-HDLC. Each CTP Series port is connected to a different VLAN. |
| Port mirroring | The CTP Series is able to port-mirror any transmit or any receive up to 10 local or remote destinations. |
| Analog voice—4WE&M | The CTP Series supports analog 4WE&M type I, II,and V interfaces with software selectable transmit and receive-level adjustments per interface. |
| Analog voice—2WFXS | The CTP Series supports analog 2WFXS loop start, ground start, and PLAR modes with software selectable transmit and receive-level adjustments per interface. |
| Analog voice—2WFXO | The CTP Series support analog 2WFXO loop start and ground start modes with software selectable transmit and receive-level adjustments per interface. |
| IRIG-B | The CTP Series supports an inter-range instrumentation group time code (IRIG-B) signal to be transported through an IP network. IRIG-B encodes day of year, hour, minute, and second data on a 1-KHz carrier frequency, with an update rate of once per second. |
| Primary Circuit to Packet Solutions | |
| SS7 transport over IP | Provides transport of dedicated T1 or E1 SS7 links over the IP/ MPLS network. |
| TDM over IP solution | The provisioning of point-to-point TDM trunks over the IP network does not require changes to the TDM equipment. |
| PBX interconnect over IP solution | Provides E1 and T1 trunking for PBX interconnection over the IP network. |
| PBX Extension over IP with 2WFXS/2WFXO | Provides two-wire analog PBX to phone extensions over IP and two-wire PBX to PBX/central office connections over IP. Private- line automatic ringdown (PLAR) is also supported. |
| Leased line extension over IP solution | Supports standards-based encapsulation and DS0 bundling. IETF PWE3 RFCs, SAToP and CESoPSN are supported. |
| Radio over IP solution | Allows for connectivity of analog and digital radios over IP networks. |
| Serial encryption over IP solution | Provides transport of KG/KIV bit-synchronous cipher text across an IP network. |
| T1 and E1 backup over IP | Point-to-point T1 or E1 circuits can be automatically backed up over the IP/MPLS network. |
Accessories
| Upgrades | |
| CTP-Fiber-PMC | Fiber PMC card for CTP2000 line to support up to 2 SFP modules |
| CTP-SFP-1GE-T | Small form-factor pluggable 1000BASE-T Gigabit Ethernet module (uses Cat 5 cable) |
| CTP-SFP-1GE-SX | Small form -factor pluggable 1000BASE-SX Gigabit Ethernet optic module |
| CTP-SFP-1GE-LX | Small form-factor pluggable 1000BASE-LX Gigabit Ethernet optic module |
| Interface Modules | |
| CTP2000-IM-8P-T1E1 | 8-port T1/E1 RJ48 interface module |
| CTP2000-IM-8P | 8-port serial interface module—EIA530/V.11/RS- 422/X.21, RS-232/V.24, V.35 |
| CTP2000-IM-8P-MS | 8-port serial interface module—EIA530/V.11/RS- 422/X.21, RS-232/V.24, V.35, 4TWO, HQ Analog, IRIG |
| CTP2000-IM-4WEM | 8-port 4WE&M analog voice module |
| 4WEM-RTM | 8-port 4WE&M 8-port rear transition module |
| CTP2000-IM-2WFXS | 24-port 2WFXS analog voice module |
| 2WFXS-RTM | 24-port 2WFXS rear transition module |
| CTP2000-IM-2WFXO | 12-port 2WFXO analog voice module |
| 2WFXO-RTM | 12-port 2WFXO rear transition module |
| Spares | |
| CTP2000-PRC-S | Processor spare |
| CTP2000-RTC-S | Rear transition module spare |
| CTP2008-REC-RMK | CTP2008 recessed rack mount kit |
| CTP-CBL-4Q | Cable—100 pin to four (4) DB-25 DCE for CTP2000 line |
| CTP-CBL-4Q-DTE | Cable—100 pin to four (4) DB-25 DTE for CTP2000 line |
| CTP-CBL-4Q-Y | Redundancy cable for connections between two CTP Series platforms |
| CTP-CLK-MAIN | Clock main rear transition module for CTP2000 line |
| CTP-CLK-SPOKE | Clock spoke rear transition module for CTP2000 line |
| CTP Series Software | |
| CTP-OS-4G | Current software on 4G CompactFlash card |
| CTP-CF-4G-S | 4G CompactFlash spare, no CTPOS |
| CTPView Network Management System Hardware/Software | |
| CTPVIEW-SVR-1 | CTPView Network Management System server hardware |
| CTPVIEW-SW | CTPView Network Management System software |
Be the first to review “JUNIPER CTP2008-AC-03 CHASSIS”
You must be logged in to post a review.
Related products
Reviews
There are no reviews yet.